AF Board MB Board Switching Regulator Interval Views Circuit Boards Location Overall Block Diagram System Control Block Diagram Signal Processor Block Diagram Audio Block Diagram Video Block Diagram Interface Control Block Diagram Frame Schematic Diagram Printed Wiring Boards and Schematic Diagrams AF Printed Wiring Board ER Printed Wiring Board MB Printed Wiring Board MB Servo Schematic Diagram MS Printed Wiring Board SW Printed Wiring Board SW Switch Schematic Diagram General Description Starting Test Mode Syscon Diagnosis Drive Auto Adjustment Drive Manual Operation Mecha Aging Emergency History Version Information Video Level Adjustment If Con Self Diagnostic Function Refer to 2 Remove the MB board.
Wow and flutter: Less than detected. AUDIO jacks are measured. When you. Specifications and design are subject to. Corporation has determined that this. Check the area of your repair for unsoldered or poorly-soldered.
Check the entire board surface for solder splashes. Check the interboard wiring to ensure that no wires are "pinched". Look for unauthorized replacement parts, particularly transis-.
Point them out. Look for parts which, though functioning, show obvious signs. Point them out to the customer and recommend. Recommend the replacement of any such line cord to the cus-. Check the antenna terminals, metal trim, "metallized" knobs,. The use of optical instrument with this product will increase eye. Use of controls or adjustments or performance of procedures. After correcting the original service problem, perform the following. The AC leakage from any exposed metal part to earth ground and.
A commercial leakage tester, such as the Simpson or RCA. Follow the manufacturers' instructions to use these. The Data Precision Measuring the voltage drop across a resistor by means of a. VOM or battery-operated AC volmeter. The "limit" indication. Nearly all battery operated. Boards requiring use of unleaded solder are printed with the lead-. Caution: Some printed circuit boards may not come printed with.
Unleaded solder has the following characteristics. Ordinary soldering irons can be used but the iron tip has to be. Soldering irons using a temperature regulator should be set to. Caution: The printed pattern copper foil may peel away if the. Unleaded solder is more viscous sticky, less prone to flow than. It is best to use only unleaded solder but unleaded solder may also. About this Manual Notes about the Discs Index to Parts and Controls Hooking Up the Player Step 1: Unpacking Step 2: Inserting Batteries into the Remote Step 3: Connecting the Video Cords Step 4: Connecting the Audio Cords Step 5: Connecting the Power Cords Step 6: Quick Setup Playing Discs Before operating this player, please read this manual thoroughly and retain it for future reference.
Check that the player's operating voltage is identical with your local power supply. To disconnect the AC power cord, grasp the plug itself; never pull the cord. For the model supplied with the AC plug adaptor If the AC plug of your unit does not fit into the wall autlet, attach the supplied AC plug adaptor. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.
If you don't, the disc may be damaged. On adjusting volume Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.
On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. On cleaning discs Do not use a commercially available cleaning disc.
It may cause a malfunction. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma Display Panel televisions and projection televisions are susceptible to this. Search mode. The model and serial numbers are located at the rear of the unit. Refer to them. If this product is not working properly, please call for.
Peace of Mind Warranty Replacement service. For other product related questions please contact our Customer. Information Service Centre at or write to us at:. The use of optical instruments with. As the laser beam used in. You are cautioned that any change. This equipment has been tested. These limits are designed to.
0コメント